How to Know What Size Wax Ring For Toilet

It is difficult to measure the exact size of the wax ring just by looking at your toilet. You can only determine the size of the toilet wax ring if you remove the whole fitting from its base. This will enable you to remove and measure out the component you need to replace.

If you think that your toilet has problems with the wax ring, it is important to know where to begin in order to acquire the correct size you need to buy. Here is a list of things you need to perform before you can get hold of that wax ring set under the toilet seat.

1. Remove Excess Water from the Tank

It is important to drain the remaining water in the tank before unmounting the toilet seat from its base. So first off, you need to shut off supply of water going to the toilet tank valve. This will ensure that after the tank has been drained, no more water will go into the bowl. If possible, try to sponge the tank dry before going to the next procedure.

2. Disconnect Water Supply Line

Disconnecting the pipe from the supply line can cause some water to spill around the workspace. So you better get some towels and a bucket to avoid this from happening. When you are ready, you can now loosen the nuts and remove them from its connection from the floor.

If your toilet has been around for quite some time already, you may need to apply some penetrating oils that will enable to seep through the corroded bolts. Try not to break the anchor flange of the toilet by moderately applying pressure when loosening the bolts.

3. Dismantle the Tank

If you think that you don’t have enough space to work on with a heavy toilet, try dismantling the tank from the bowl first. This will ease out the burden by separating the tank before unmounting the toilet seat from the ground.

4. Remove the Wax Ring

Try to use disposable gloves before doing this. Likewise, it is important to have proper ventilation by opening the windows. Understandably, it can release some unwanted odor from the pipes, so you might as well wear masks. The mounting bolts must be removed and the anchor flange must be checked as well for possible damage. You can then unmount the old wax ring before covering the drain with old rags big enough not to fall into the drain pipe.

5. Determine the Size of the Wax Ring

After removing the wax ring, try to measure its diameter using a tape measure. Some toilets that have been abandoned or unused for a long period of time may have damaged or missing wax rings. Measuring the elbow neck can be an option to determine the dimension of the old wax ring.

If you need to measure the thickness of the wax ring, check out how the toilet is being set up onto the floor. Sometimes the toilet flange is located below the floor level, so you need to acquire the double thick type. Meanwhile, if you think it is just leveled on the floor, a standard type wax ring will suffice.

How to Install a Wall Hung Toilet

More and more people are opting to use wall hung toilets over the traditional floor models. In fact, these types of toilets are now mostly found in newly built and renovated homes where a more contemporary or modern design is being incorporated. While it sounds to be difficult at first, as it requires a different method of installation, setting up a wall hung toilet is actually doable as a do-it-yourself (DIY) project. Also, you might want to get the help of one or two persons, as such a unit is much fragile and heavier than traditional floor models. Here is how to install a wall hung toilet:

1. Prepare Your Wall.

Obviously, you need to perform some preparations to your wall before you will be able to mount the toilet, considering other installations, such as the waste water tube and the water supply line. Recheck the measurements and make sure that the wall is ready for the project to start. Typically, studs must protrude from the wall at least 2.125 inch to give you a frame that is strong enough to hold the toilet.

2. Install The Bowl To The Supports.

After making sure that the pipes are in the right place and that the supports are strong enough, you can then lift the bowl and affix it to the supports. Attach it through holes that are drilled into the support studs, with the provided cap nuts and washers. After securing it to the wall, affix the gasket to the waste tube and connect the bowl to the sewer pipe.

3. Set Up The Tank Onto The Toilet.

After the toilet is properly positioned, place the tank onto the bowl, with the option to either insert the tank into the wall or attach it to the outside of the wall, depending on the model you are having. No matter how you do it, connecting the tank to the bowl is generally a universal process. Place the rubber toilet gasket in position and the rubber gaskets between the bolts and screws. Jiggle the tank a little to ensure a strong fit and, finally, screw the tank onto the bowl for a secure installation.

4. Connect The Water Supply.

With the toilet in position, it is time to start working on its water supply. With the supply lines near the toilet, connect a flexible pipe to the water supply with the compression fittings and then connect it to the tank. Tighten the fittings and turn the water supply on. Check for leaks to ensure that you will not be having such problems after you complete the project.

5. Test The Toilet.

With the tank full of water, flush it several times to make sure that the toilet quickly drains waste and normally fills up. You can try sitting on the tank to see if it is securely fastened to the wall and does not move. Seal the back of the toilet with some caulking material to finish things up with a clean look.

There you have it. By following the above-mentioned steps, you will be able to successfully install a wall hung toilet in your home!

How to Install a Toilet Flapper

When water in your toilet seems to trickle through the bowl even long after you have flushed it, the problem is most likely that you have a worn-out rubber flapper, which is located at the bottom of the tank. This component works by lifting when you flush the toilet, letting the water flow into the bowl. As the tank is emptied, the flapper will sink to block the opening, allowing the tank to refill. Since this part is made of rubber it can harden and then break down over time, though it is designed to be durable.

When this happens, it will no longer provide a perfect seal that is tight enough to stop the flow of water as it should. As a result, there will emerge an audible trickle that is punctuated by occasional surges of water topping off the tank. While you can first jiggle the handle to try to stop the trickle, this trick is just a temporary solution that will eventually stop working. A worn-out flapper can drive up water costs, and if the supply line also transports warm water to prevent condensation, your heating bill will also go up.

Fortunately for you, a flapper is just an inexpensive component of your toilet that you can easily replace. If you have narrowed down you running toilet problem to this component, you can quickly fix it. With the necessary tools—pair of pliers and screwdriver—at hand, just follow these steps:

1. Cut The Water Supply To The Tank.

Changing your old flapper for a new one is just a quick job that starts by cutting the water supply to the tank, which is usually located below the tank or behind the bowl. Flush the toilet after turning off the water supply to drain the tank. If you notice that the supply valve is weak or corroded, it is recommended to turn the water supply off at the main source. You can dry out the remaining water by using a sponge if you want, though this is not really necessary.

2. Note The Length Of The Chain.

After flushing the water in the tank, note the length of the chain that connects the flapper to the flush handle. This will save you time when you are about to install the new flapper.

3. Remove The Old Flapper.

To remove the old toilet flapper, unhinge first the chain connecting it to the toilet handle rod. Then, pull out the rear or each side of the flapper to unhook it from the flush valve. If such a component is connected by a circular ring around the tube, you can remove the refill tube from the overflow pipe. After removing the chain, you can now remove the old flapper by sliding it up and off of the overflow pipe. Another way to do this is unhooking the flapper ears from the overflow pipe. If your toilet has plastic flush valves, you might need to bend the flapper ears out and off the pins that are attached to the flush valve.

4. Get The Essential Information Needed For Buying The New Flapper.

After removing the old flapper, take note of the toilet model number and the toilet manufacturer. You can usually find the model number on the inside at the back of the tank and the name of the manufacturer stamped outside of the bowl near the seat hinges. Take the information you have noted and your old flapper to the hardware, home improvement or plumbing supply store near you to obtain the right replacement flapper for your toilet tank. Most likely, the store should have information on the right replacement flapper and settings for an adjustable one. Before you leave, do not forget to get a beaded metal chain replacement for the flapper.

5. Prepare The New Flapper.

For the most common toilet configuration, it has the flapper attached by the ears located on the sides of the flush valve. If this is how your toilet unit is made, then you should cut off the ring on the back of the flapper. If you are having a fill valve that does not have side hooks for the flapper, you need to use the ring to slide such a component into place.

6. Install The New Flapper.

To install the new flapper, slide it down and over the overflow pipe until the ring touches the tank’s bottom, with the flapper bulb centered on the valve opening. Put the new component into place, hooking each of its ears onto the flush valve. Then, the chain onto the toilet handle rod and make adjustments if necessary. Take note that the chain needs to be long enough to allow the flapper to sit firmly in place, but not exceedingly long that it would get caught under the flapper when the water rushes out.

7. Perform The Final Steps.

Turn the water back on and do the necessary tests, which include flushing a couple of times or more.

More Useful Tips and Warnings

If you are not sure if the replacement flapper was a correct one to begin with, you can seek professional advice or check out your toilet’s manual or the manufacturer’s website to ensure you will be getting the right one. Usually, you can find toilet flapper replacement kits in any hardware store, coming with complete and easy-to-follow instructions.

While you see that the water inside the tank looks grungy, it is clean water, so there is no reason to be afraid of putting your hands inside. You should also take note of the common installation mistakes and how to avoid them, including the failure to remove unnecessary parts from universal replacement flappers and the improper adjustments of the flush chain. Moreover, be careful not to crack the ceramic lid of the tank when addressing a flapper problem.

A toilet that is constantly running or not flush well can be annoying, not to mention that it can waste water. The good news is, a flapper problem is just easy to fix, given the right steps.

How to Get Hard Water Stains Out of Toilet Bowl

One of the very challenging tasks to do at home is cleaning the toilet. Some households even seek the assistance of professionals to do the job for them. However, the secret to make this job as easy as possible is to perform some daily cleaning routines. This will ensure that hard to remove stains from the toilet bowl can be avoided.

Cleaning the toilet even gets more challenging with the presence of hard water stains that could build up on key areas of the bathroom. Such areas include sinks, toilets, showers and faucets. This can be addressed with the use of different cleaning products that can be purchased on the market. Alternatively, others utilize household chemicals as they are equally effective in removing unsightly stains from the toilet bowl.

1. Vinegar with Baking Soda

An effective combination of vinegar and baking soda will be effective enough to take out hard water stains from the toilet bowl.

  • This can be done by pouring one cup of vinegar first and try to apply it vigorously with a brush.
  • Leave it for nearly a minute before adding about a cup of baking soda.
  • Make it work by adding a couple cups of vinegar into it. Leave the combination to fizz for about ten minutes.
  • After that, ensure that the whole surface of the toilet bowl is included by scrubbing it with a toilet brush.
  • Before flushing the toilet, spend a couple of minutes to allow the solution to penetrate and try brush off the remaining stain if necessary.

2. Vinegar and Borax Combination

Borax is another excellent all-around cleaning agent that can be used to eliminate hard water stains from the toilet.

  • Measure out one-fourth cup of borax and try to scrub it around the bowl using a toilet brush.
  • You can then add a cup of vinegar and simply leave the mixture on the bowl for a matter of twenty minutes.
  • In conclusion, scrub the bowl to remove the stain using a toilet brush.

3. Try to Use Borax Paste

Some very stubborn water stains can be removed by applying borax paste onto it.

  • Begin by turning off water supply into the toilet tank. This will ensure that no water will cover the hard water stains on the toilet bowl when applying the solution.
  • Create a borax paste by mixing about half a cup of borax with vinegar that could form a sort of think paste.
  • Try to spread the solution on the stained water bowl to penetrate. This time, the borax will begin to harden. Just don’t try to add vinegar yet, only when you are ready.
  • Spend another fifteen to twenty minutes before scrubbing the stain and the paste off the bowl.
  • This time, try to use a bigger brush to scrub off the borax paste mixed with some elbow grease to soften the paste and the stains for easy removal.
  • Reconnect the water supply and begin flushing the remaining solution together with the stain.

How to Find Kohler Toilet Model Number

Repairing a toilet can be very challenging for any household. It can even be a lot stressful if you are not certain of the model if ever your toilet needs some replacement parts. The dilemma is that you can never fix a broken part if you do not know which components will match the one you need.

Well, it can be resolved if you are keen about specific details of components needed for fixing your toilet. Here are a few comprehensive points that you can do to figure out which Kohler toilet model number is the one at your possession. Accordingly, you can easily find the components for fixing it.

1. Searching at the Bottom for Kohler Toilet Model Number

If your toilet has a tank, try to remove it gently and put it on the floor. If possible, set the bottom to face in an upward position. The manufacturer’s number can be found on the bottom at the side of the lid of the water tank. It is commonly stamped or painted on the lid, but sometimes it can be handwritten if there was an instance that it has been replaced by the plumber.

2. Look Inside the Water Tank

If you have not found it at the bottom side of the tank, try locating it inside the tank itself. It is commonly located exactly on top the water line which can be painted or stamped. Some are situated below the water line and they are painted with waterproof material.

If you can hardly see the mark, use a flashlight to make it more visible. Most of the tank can be stained with hard water so it should be difficult to pinpoint the location without some light. Some stampings are also located at the tank bottom, so make sure you include that location in your search.

3. Use Some Cloth to Clean the Tank

Try to dry out the tank to provide ease in finding what you are looking for. When the tank is dry, use some cloth to wipe the inside of the tank. This will enable you to spread the dirt along the crevices or indentations exactly where the name or number is located. As a result, it can’t clean the tank but will allow you to pinpoint the location of the details you need to have.

4. Search Near the Toilet Seat

Most modern toilets such as those made by Kohler put their marks in between the toilet seats and the bolts. These are located on the bowl and near the toilet seat but not on the seat itself. The toilet seat might come from another manufacturer, so do not consider the one written here.

There are many toilet products that can confuse anybody when buying replacement parts. Well, it doesn’t have to be that stressful, since there are plenty of ways to search for the Kohler toilet model number of your toilet. If you still can’t locate what you are searching for, try to seek the assistance of a professional. Your plumber, for instance, might be more knowledgeable about certain details of your toilet than you do.

Why Do Toilets Get Clogged

Are you plunging your toilet at least once a week? Well, it is definitely bothersome. Here are the most probable reasons why your toilet just keeps on clogging:

You Are Flushing Things That Should Not Be There In The First Place.

The only stuff that should be flushed down your toilet is human waste or toilet paper, and nothing else that would not break down in the water. Common things that can cause clogs include facial tissues, tampons, condoms, Q tips or cotton swabs, diapers and dental floss. Make sure you have a garbage basket next to your toilet, where you can throw these things into.

There Is Something Stuck In The Toilet Trap.

A toilet trap is the S-shaped tube that separates the toilet from the drain line and keeps nasty sewer gases from entering your home. Sometimes, this part can get clogged due to something that was flushed down the toilet and got stuck in the trap. While a plunger can send all the debris down the drain and solve the problem, hard objects with complicated shapes can stay in the trap because they could not get through the trap’s S-curve. In this case, you have to remove your toilet off the floor and remove the clog from the bottom. If you are uncomfortable with this task, it is best to hire a professional to get the job done to avoid mistakes that can lead to even more serious problems and more costs. If you are doing it yourself, make sure you replace the wax ring, which is a seal that keeps wastewater from leaking into your bathroom.

You Have a Blocked Plumbing Vent.

Your toilet drain most likely vents out through your roof, helping your toilet with flushing properly. Now, if this vent is blocked by something, like a bird’s nest, your toilet will not flush properly. The slow flushing means that larger loads would not get flushed completely, which can result to a recurring clog that keeps you using your plunger. Clearing the plumbing vent requires you to work from the roof, so it might be best to let the professionals do it.

The Flapper Is Not Opening Completely.

The flapper is a toilet component that allows water to flow from the tank down into the bowl when you flush it. And if it does not open completely, it will not release enough amount of water that gives you a powerful flushing pressure. You can fix this problem by adjusting the chain that connects it to the flush handle.

There Are Problems To Your Sewer Line.

If you are experiencing clogs not just in your toilet, but also in other drains, you might be having some kind of problem in your sewer line. Causes could be tree roots growing into the line or a partial clog in the line that was never removed from plunging. To clear out your sewer line, you will definitely need a professional.

You Have An Old, Low-Flow Toilet.

If you are using an older toilet model, it just might not have enough flushing pressure. As you can see, low-flow toilets did not impress homeowners when they first came out, so you might want to replace your unit with a more modern version.

Now, when you experience a toilet clog, you already know where to check with the list of problems above.

How to Replace the Guts of a Toilet

As your toilet’s innards—the flash valve, overflow tube, fill valve, etc.—have been dealing with gallons of water every day for years, it is possible that they have become rusty, with their rubber and plastic components deteriorating or even breaking. Instead of replacing your entire toilet unit, you can just replace its guts. Here are the steps to follow:

  • Secure the things that you will need for the project, including an adjustable wrench, pipe wrench, flat-blade screwdriver, scissors, tank-to-bowl gasket, tank bolt gaskets, fill valve gasket, overflow tube and flush valve, fill valve, tank bolts, refill tube and towels.
  • Turn of the water supply valve beneath the tank. Remove the tank lid and make sure you place it on a towel to prevent damage. Drain the tank, and if the handle does not work, lift the flap with your hand. Get rid of the remaining water in the tank by soaking it with a towel.
  • Using an adjustable wrench, rotate the nut that holds the supply line to the tank counterclockwise to remove it. Now, you should be able to access the fill-valve nut, so remove it by turning its nut counterclockwise and then you will be able to release the fill valve.
  • To stabilize the toilet bolts inside the tank, place a flat-blade screwdriver into their slot. Then, loosen the toilet bolt nuts beneath the bowl and the tank with an adjustable wrench.
  • Lift off the tank and lay it on a towel on the floor to access its bottom. Remove the rubber gaskets that surround the toilet bolts and then the nut that holds the flush valve using a pipe wrench. Grab the overflow tube connecting to the flush valve and then pull the tube and valve from the tank.

  • Place the gasket around the threads that come with the new flush valve and overflow tube. Most of the time, the flapper is already attached to the valve and tube, and if it is not, snap it over the plastic prongs located at the bottom of the overflow tube. Using a pipe wrench, screw the nuts coming with the flush valve to the threads found beneath the toilet tank. Then, cover the nuts and threads with the new tank-to-bowl gasket.
  • To start setting the tank on the bowl, thread the new gaskets onto the new tank bolts, which you should insert through the holes in the bowl and the tank. Tighten the nuts using an adjustable wrench.
  • Place the fill valve gasket over the end of the new fill valve and then insert the threads of the valve through the hole at the tank’s bottom. Screw the nut onto the fill valve and hand-tighten the nut to secure the valve in the tank. Attach the supply line back to the fill valve, tightening it with an adjustable wrench.
  • Slide the refill tube onto the fill valve connector and position the refill tube over the overflow tube. Cut the refill tube’s connection with scissors if it is too long.
  • Connect the chain from the flush handle to the flapper and replace the components in a reverse order of how you removed them. Turn the water supply back on to fill the tank with water. You should now be able to see the float stopping the water from flowing at the desired level. Return the tank lid back in place.

By following these steps, you will be able to replace the guts of your toilet.

How to Fix Toilet Flush Pressure

A toilet that does not flush properly due to insufficient pressure can put you in uncomfortable situations, such as not being able to leave the bathroom immediately after use, as you have to flush the toilet multiple times, wasting water in the process. Also, this problem will make it more difficult for you to keep your toilet clean. Now, if you want to restore or improve your toilet’s overall flushing pressure, follow these steps:

1. Check Your Toilet If It Is Clogged.

You can begin by pouring in about a gallon of water into the toilet and then flushing it. If it does not flush properly, then most likely you have a clogged toilet. You can fix such a problem using a standard plunger for minor clogs or an auger for more serious ones. If you do not have a clog, then you can move on to the next step.

2. Check If The Water Is At The Right Level.

Remove the tank cover and check if the water level reaches the designated line. If it is not, then you have to use the float assembly, which is located just inside the tank, to adjust the water to the right level.

3. Try To Find Any Clogs Around The Rim.

There is a series of flush holes located around the rim of the bowl, which can sometimes get clogged, decreasing the water pressure when you flush your toilet. To clear up any blockage that may exist in these holes, you can try using a coat hanger, bobby pin or a small drill bit and push it through them. When you think you have cleared them up, flush your toilet to check for some improvements in flushing pressure.

4. Clean Your Toilet.

Before you start cleaning, make sure you have completely turned off the water supply valve that you can find at the back portion of your toilet. When there is no water running into the unit, you can pour in some bleach into the bowl. Let it sit for about 15 to 20 minutes and flush it, to let the bleach work its way naturally through the toilet system, cleaning out any build-up that has been reducing your toilet’s flush pressure. After turning the water supply back on, flush your toilet a few more times to completely wash the bleach down.

5. Apply Some Vinegar.

When performing a vinegar soak, you should first open the lid of the tank. Then, remove the rubber fill hose that is located on top of the overflow tube. Place a funnel on the tube inside of the tank and pour some white vinegar into the tube through the funnel. Let the vinegar sit in for at least 2 hours to fully disinfect and help loosen build-up in the toilet system. Finally, replace everything and flush your toilet.

Taking the time to perform these steps should improve your toilet’s overall flushing pressure. If you do not see any difference, then maybe it is time to call in the professionals to get the job done.

How to Fix Low Water Pressure in Toilet

How toilets are designed has not actually changed much over the years, where most units being used today contain a water storage tank at the back that holds water above a flapper. When you flush it, the flapper raises to release water into the bowl and then down the drain pipe. Now, if you are experiencing low water pressure in your toilet, it can be caused by many things, including clogged holes around the rim, insufficient water supply and low water level in the tank. To help you with such a problem and increase the flushing power of your toilet, here are some quick fixes that you can perform:

1. Check If The Rim Is Clogged And Fix It.

Water flows to the toilet bowl from the tank through a set of small holes that are located on the underside of the rim. If they are clogged by certain substances, such as lime, the water cannot flow into the bowl at a force that it should normally does. You can use a small mirror to get a good view of the underside rim and check for signs of clogging. Using a nylon brush, clear the holes of any blockage and increase the toilet’s overall flushing pressure.

2. Make Sure That The Water Valve Is Completely Opened.

Most toilets are fed water through a small water valve that is positioned on the floor or wall near the back of the unit. Now, a partially closed valve can affect the fill performance of the toilet tank. Find this valve and make sure that it is completely “on” by turning it counterclockwise with your hand until it stops for the best flushing performance. For some toilet models, they would only require a quarter turn to be fully open.

3. Adjust The Water Level Inside The Tank.

To be able to flush properly, the water level in the tank must be at the right level. Remove the tank lid and try to see if the water level in your toilet tank sits about an inch below the overflow tube. If the water level is lower, you can adjust the float to increase it. If your unit has a ball float, you can turn the screw on top of its fill valve clockwise to get the job done. If your unit uses a cylinder float valve attached to its fill valve, then you can squeeze the clip on the side of the float and pull up the float until you reach the desired water level inside the tank.

Ignoring to fix a slow-flushing toilet can result to clogs along the drain system, which can be very bothersome—it can create a mess that comes with dirty water. Also, it can cause the toilet to be flushed multiple times in a single use, which means water wastage. So, you should fix such a problem as soon as possible. After all, it can be as easy as following the steps provided above.

How to Clean a Toilet with Coke

Coke is not just a tasty beverage, but is also a liquid with mild acidity that makes it useful for cleaning, particularly on toilets. It works because of the gentle phosphoric and carbonic qualities that it contains. Its acidity comes from the carbonation that occurs in it, and not from the flavorings that are put in it, which means that Diet Coke, club soda, and many other carbonated beverages can work just as well as Regular Coke, though these substitutes are rarely as cheap. So, if you are searching for a non-toxic solution to deal with toilet lime scale without spending a hefty amount of money, like when you use those expensive toilet bowl cleaners, Coke is the way to go! Check out these tips on cleaning your toilet with Coke.

For Mild Stains

Coke can be effective in cleaning mild toilet stains. Follow these steps:

  • Open a can or a bottle of Coke and measure out a cup or two, as you will not need much to clean your toilet bowl.
  • Pour the Coke into the bowl, specifically around its rim, and let it flow over the stains, making sure all smears are given an even coating of Coke. Though the beverage would appear to wash straight into the bottom of the toilet, a thin coat would remain on the stains. For stains that are high in the bowl and are difficult to reach, you can try soaking a rag with Coke and then apply it by hand. If you do not want to get your hands dirty, you can instead use a spray bottle filled with the beverage.
  • Let the Coke sit for a while, as the longer it stays in the bowl, the more time you are giving the acids in the beverage to break the stains and other dirt down. You can let it sit for at least 60 minutes without disturbing it, but for best results, you can pour the Coke in before going to bed and let it sit in your toilet bowl overnight.
  • Flush the toilet. After the Coke had sit in your bowl, its acids should have loosened the stains that have built up on it. By flushing the toilet, the stains should be rinsed away with the water. Flush as many times as needed.

At this point, you should be able to see how well this beverage has removed your toilet stains. However, take note that while it usually works well for common built-up mineral stains and rings in toilets, it might not completely remove every stain. So if needed, you can repeat the steps mentioned above. But if the stains would not just go away, consider the following tips.

Removing Hard Stains with Coke

1. Perform a lot of scrubbing. If simple flushing does not remove your toilet stains, then using a toilet brush is your best solution. This household item’s mechanical action will further loosen the stains that have built up on the bowl and help remove them after being treated with Coke. For best results, perform the task before and after applying the Coke. Hence, scrub the stains, apply the beverage and let it sit in, scrub once again and then flush the toilet to rinse away the stains. Remember to wear gloves while scrubbing and wash your hands afterwards, especially when you hate germs getting into you.

2. Another solution to boost the effect of Coke on toilet stains is using heat. Basically, chemical reactions will occur more quickly at high temperatures, and the acid reaction allowing this beverage to remove toilet stains is no exception. Now, if you have hard-to-remove stains, you can try heating up the Coke in the microwave and then apply it to the bowl. It does not mean that it should be boiling hot, but it should be hot to the touch for best results, so remember to use caution when performing this step. Heating carbonated beverage will make the liquid fizz slightly more than normal, so it is best to wear gloves to avoid getting your hands splashed with drops of hot soda. Moreover, you should never microwave Coke in a sealed container, especially one that is made of metal, as it can lead to dangerous explosions. Instead, pour Coke into a microwave-safe glass and then heat it.

3. You can use Coke together with other household cleaning solutions. As mentioned above, while the beverage can remove many stains, it does not always work for the job. So, there might be situations where you have to pair it with other cleaning chemicals to get rid of toilet stains. One popular toilet cleaning method is mixing 1/4 cup of baking soda and 1/2 cup of vinegar (in some cases added with 2 teaspoons of borax) into 1/2 gallon of water; applying the mixture to your toilet bowl; scrubbing; and then waiting for 60 minutes before flushing. Then, follow it up with the Coke treatment as needed.

If you have mold problems, try mixing 2 parts of water with 1 part hydrogen peroxide in a spray bottle. Spray the solution on to the problem surface, let it sit for at least 60 minutes and scrub until you have dissolved the mold. You can then use Coke to remove any residual scaling or stains around the moldy spot.

Another toilet cleaning method is mixing 1 part of Coke, 1 part of lemon juice and 2 parts of borax. Apply the mixture to your bowl, let it sit for about an hour and then scrub the stains off.

4. Always know when Coke is not the best choice. First, it is not effective for getting rid of grease, fat or oil-based stains, which you can address better by using dish detergent or a stronger acid. Also, it is good at killing germs, where in fact, it would leave a sugary residue that would feed certain types of bacteria. Moreover, Coke will not remove any stain caused by dye, ink or a coloring pigment.

The acidity in Coke that gives it a cleaning effect does not make it unsafe to consume, where there are other popular drinks that are even more acidic, such as orange juice.