Bathtub Spout Leaking and Tips for Fixing It

Rising water bills, ugly stains, and low water pressure are just a few of the problems you are faced with when you have a leaky bathtub spout. If this goes on unattended, you can end up with water and mold buildup under your floor, as well as a dark spot on your sheet rock in the tub. Sometimes, the cause is just hard water build up. But other times it is because of loose or defective faucet parts. To avoid the hassle of these problems, repair a leaking bathtub faucet immediately.

Materials

  • Bath socket wrench or vice grip pliers
  • Plumber’s grease
  • Monkey wrench
  • Teflon tape
  • Philips screwdriver
  • Tub caulk
  • Flat-head screwdriver
  • Rags
  • Jar gripper
  • Hair dryer

Steps

1. Shut off the water intake to your house.

2. Drain any remaining water in the pipes by opening the hot and cold valves on the spout.

3. Use a flat-head screwdriver to remove the faucet handle inserts of the hot and cold valves.

4. Unscrew the handles from the wall using a Philips screwdriver. If the faucet seems corroded or welded on, use a hair dryer to heat and loosen the handles. If this still doesn’t work, call a plumber. Do not force it to avoid breaking the handles.

5. Use your hand to unscrew the trim and collar from the wall for both handles.

6. Remove the stem bonnet using a bath socket wrench or vice grip.

7. Remove the seat. Stick the seat wrench deep into the opening where the faucet was. Once the elongated end has a good hold of the seat, turn it counterclockwise to remove.

8. Check the parts you have removed and identify which ones need to be replaced.

9. Buy the replacements at the nearest hardware or plumbing store.

10. Start replacing the parts, beginning with the stem bonnet. Make sure to apply plumber’s grease on each new part before screwing them on.

11. Unscrew the seat washer screw, then peel off the rubber seat washer. Grease both parts before screwing them back on. Use a seat wrench to put the seat back in place and tighten it with your hand. Check if it is tightly sealed but easy to remove by hand.

12. Remove the bonnet washer from the end of the bonnet, apply some plumber’s grease on it, then replace the bonnet.

13. Use a flat-head screwdriver to pry the rubber packing washer from the packing nut. Apply plumber’s grease on the threads on the front of the stem. Insert the packing nut into the middle of the stem bonnet.

14. Grease the new packing washer, then place it in front of the packing nut.

15. Apply some pipe joint compound to the threads in your bonnet, then insert the bonnet. Make sure it is securely fixed in place by tightening with a socket wrench or vice grip.

16. Replace the faucet collar, trim, handle, screw, and insert for both faucets.

17. Turn the water back on and check if there is still a leak in your bathtub spout.

Tips

  • If there is still a leak even after you have replaced the faucet, call a plumber.
  • Lay out the parts you remove on a rag in a safe place inside the bathroom to avoid losing or damaging them.
  • If there are any damaged parts that need to be replaced, do not throw them away. Bring them with you to the hardware or plumbing store so you can get the correct replacements.

Boiler Pressure Relief Valve Leaking and What to Do

The pressure relief valve of your boiler is a very important part of your heating system. This is because it is a safety valve that protects your heating system from building up too much pressure. When that happens, you are faced with leaks or even the possibility of your heating system blowing up. When you notice a leak coming from your boiler pressure relief valve, attend to it immediately. Here are possible causes and solutions to fix such a problem.

1. The Relief Valve Is Defective.

Eventually, everything will give in to wear and tear. This safety valve should be checked at least every three months. If you haven’t checked it for quite some time, check it right away because unchecked valves can become rusted and closed.

IMPORTANT: Make sure to turn the power of the boiler off and allow the water to cool for about two hours. Then check the temperature first before you pull the lever.

2. The Fill Valve Is Defective.

This pressure reducing valve is designed to allow only 12psi into the boiler. If it is allowing the pressure to reach 30psi or higher, leaks can occur. To check if the fill valve is the problem, turn the boiler off, allow it to cool, drain some of the water until the pressure reaches 10psi. Don’t turn the boiler back on and wait if the gauge starts to go up again. If it does, then the fill valve may be defective.

IMPORTANT: If the fill valve reaches up to 30psi or higher and there are no leaks, shut off your boiler and call a plumber immediately because this is a very dangerous situation.

3. The Expansion Tank Is Water Logged.

This part allows water in the boiler to expand. Over time, it becomes logged with water or air starts to leak out of the tank, and when this happens the pressure relief valve will start to leak. Watch the pressure gauge when the boiler is heating, and if the pressure builds during the process, then the tank is most likely the problem and needs to be replaced.

4. The Aquastat Or Aquastat Relay Fails.

This gauge is required in most area codes, so if you don’t have one, you should have one installed. If your aquastat or its backup (the aquastat relay) is defective, the temperature of your boiler can reach a very high point. This is extremely dangerous and can cause your relief valve to blow off. You must immediately turn off your boiler and call a plumber right away.

5. The Hot Water Coil Has Developed a Pin In It.

Some boilers have a tankless water heater or what is also known as a hot water coil. Sometimes, this coil will develop a pin in it, and this causes pressure to seep into the boiler and leads to leaks in the pressure relief valve. Turn off the water to the coil and check if the pressure stops rising. If it rises with the water off, the hot water coil is the problem.

REMINDER: Because repairing a leak in the relief valve of a boiler involves handling water that can be extremely hot or boiler parts that are sensitive, there is always a risk of endangering yourself or damaging your heating system. So if you are not too experienced with handling such repairs, it is best to call a professional plumber.

Delta Faucet Leaking and How to Fix It

Leaving a leaky faucet alone can waste a lot of water in a single day. Actually, it can lead to wasting three gallons of water daily. So, if you care about the water bill and the environment, of course, you should be able to fix the leaking faucet right away.

To start with, you need a set of tools that you can use to make the job a lot easier. The tools include 1/8-inch Allen wrench, tongue-and-groove pliers, needle-nose pliers, and screwdriver. Basically, this is considered by many to be a very simple DIY fixing job that you can do all by yourself. Here are some basic fixing methods that you can mimic alone or with a partner.

1. Shutting Down Water Supply

The water supply should be closed in order to avoid messing up the job you are trying to accomplish. For this reason, you need to check out the location of the valve that may often be under the sink. If possible, you can turn off the entire supply for the whole house to keep the water supply out of the way when you’re doing your job. After which, you can check if still there are water left along the pipes by opening another set of faucet.

2. Taking Off the Handle

Removing the handle is easy. You only need to take of the screw cover first. Then, you must use an Allen wrench or screwdriver to remove the screw. After doing this, you have to lift the handle off to easily remove the handle.

3. Replacing Seats and Springs

Try to look at the adjusting ring when you are going to replace the springs and seats. If you are going to replace the faucet due to some obvious leaks, you can do it from there. Simply tighten the adjusting ring using a needle-nose plier. However, if the leaks still prevail, you have to replace the springs and seats of the faucet.

4. Removing the Cap

You have to unscrew and remove the adjusting ring. After this, you have to unscrew the cap by putting a piece of cloth over the cap. This will improve the grip. You also need unscrew it with the tongue-and-groove pliers. Just don’t use too much pressure in removing the cap as it is prone to bending.

5. Replacing the Cam and Packing

Look out for the round metal stem and pull it out. This action will enable the removal of components, such as the ball and the cam and packing piece. After determining the cause of leaks from the faucet, you should replace the cam and packing to resolve the leak.

6. Removing the Seats and Spring

Check out the valve and you will be amazed to see the mechanism called the seats and springs. The tiny circular part is referred to as the seat, while the other one is called the spring that is located below the seat. If possible, you can use an Allen wrench to pry out the seats and spring. This should be done in both hot and cold water.

7. Inserting New Seat and Spring

Try to insert new replacements for the seat and spring into the holes. You also need to thread one set onto the Allen wrench via the flat side of the seat. Then, you should be able to use it on the spring’s skinny edge. Make sure that you use a wrench to tip the seat and spring into the tiny hole inside the valve. You can follow the same procedure with the other set.

8. Replacing the Ball Assembly

When fixing a problem like this, it is important to align the pin and valve into the slot of the ball.

9. Replacing the Cam and Packaging

In doing this, you must be able to align the tab on the cam with the corresponding slot on the valve.

10. Screwing the Cap on the Valve

By using only your own hands, you will be able to screw the cap on the holding. You can also replace the adjusting ring. Simply tighten it using the needle-nose pliers. Then you can now reinstall the handle.

11. Turning Water Supply Back

After installing the components in place, you can now test by turning on your water supply. This will ensure that you have fixed the leak after doing the routine.

Delta faucet can leak over time as water will eventually begin to drip. If you are faced with this dilemma, you should be able to respond to this emergency right away. Otherwise, you will definitely incur more water waste. Aside from taking care of the bill, you can also do a favor for the environment through conservation of water.

12. Investigate Any Warranty Coverage

Before personally dealing with repairs on Delta faucet leaking, make sure that it has already gone by the warranty period. Otherwise, you can void the warranty and the worst part is that you can ruin the faucet all by yourself. If it is still under warranty, you can call on the customer service personnel to address the problem that you have at home. Simply show them the proof of purchase or original sales receipt.

The transaction will only be valid if the purchase was actually made from Delta Faucet Company. You should also be aware that there are certain limits that have been stipulated under the law. If the faucet has already been over the warranty period, it is time to do your own stuff. You should be able to know which components would require fixing in the first place.

If you require help for this task, you can ask a buddy to accompany you to complete the job. Likewise, parts of the faucet should only be made by Delta because it can assure that components are compatible when you try to fix it yourself. This is very important so that you can’t waste precious time and money when dealing with such problems at home. You can also seek the advice of professionals in doing this task so that you won’t cause any more harm than good.

Hose Spigot Leaking: How to Repair It

Having a leaky hose spigot can cause you to waste gallons of water on a regular basis and end up with a huge water bill. It can also cause water damage to the surrounding area due to the constant presence of moisture. Of course, if you’re planning to sell your property, it can put off potential buyers and make them less likely to purchase your home.

Fortunately, fixing a leaking hose spigot isn’t that difficult. You can start by taking the following steps:

Tightening The Nut

Before doing anything else, check the packing nut (which is located behind the handle of the faucet) and tighten it. The packing nut can become loose over the years and cause a leak, and simply tightening it can solve the problem. Use a wrench or a pair of pliers to tighten the nut.

Adding More Packing

If taking this step isn’t effective, you might need to add more packing to the area. To do this, shut off the water valve to cut off the water supply to the faucet. Next, remove the faucet handle, take off the packing nut, and wrap Teflon tape or graphite tape around the area. Put the packing nut and the handle back on, and turn the water supply on to see if the leak is still there or not.

Replace The Washer

If tightening the nut and adding more packing doesn’t stop the leak, you’ll probably need to replace the washer in the hose bib (i.e. the heavy-duty fitting that contains the spigot and where the faucet is attached). This washer creates a seal that prevents water from leaking so, when it becomes old and/or damaged, the seal gets broken and the hose bib develops a leak.

You’ll need to buy the right washer from the hardware store (make sure it’s the right size and type). Once you have it, you can take these steps:

1. Shut off the water supply valve.

2. Use a screwdriver to remove the faucet handle.

3. Use an adjustable wrench to remove the packing nut.

4. Take out the valve stem.

5. Remove the old rubber washer. You might need to use a screwdriver to do so if the washer is worn and has stuck to the surface. Be careful when using the screwdriver to avoid damaging the hose bib.

6. Once the old washer is out, clean out the groove that it had sat on. More likely than not, you’ll find that the surface is covered with dirt, mineral deposits, corrosion, and other substances. It’s important to remove this build-up to ensure the new washer can be properly installed.

7. Insert the new washer.

8. Reinstall the washer screw to hold the new washer in place. Tighten it using a screwdriver.

9. Reinsert the valve stem then reattach the packing nut and handle. Make sure they’re tightly screwed back on.

10. Turn on the water supply valve and check if the leak is still there.

Take these steps now to stop your hose bib and spigot from leaking!

Toilet Tank Leaking Onto Floor: Tips for Fixing It

When people think of leaky toilets, they usually think of water that runs constantly from the tank and into the bowl. But, while this is the most common type of leak, homeowners have to realize that this isn’t the only problem that can arise. Sometimes, the tank can spring a leak and cause water to drip water from it and onto the floor.

If this happens in your home, you’ll need to fix it quickly since it can cause you to waste a lot of water and end up with a huge utility bill. It can also make your bathroom floor constantly wet, which can pose a safety hazard to you and your family and expose you to slips and falls.

But how exactly can you fix this problem? Well, before doing anything else, you should first determine where the leak is coming from. Since a leaky toilet tank can be caused by several things, you need to pinpoint the exact reason so you know how to proceed.

Once you know what’s causing your toilet tank to leak, you can take steps to fix it. Here are a few tips you can use:

Leak Caused by Cracks in Tank

Porcelain is a durable material, but it can break when your tank is too old or if it has been exposed to trauma. Either way, cracks can form in the surface and cause water from the tank to leak out — which can happen even if only hairline cracks are present. In this case, the best option is to replace your tank.

Leak Caused by Locknut

The locknut secures the water supply hose to the tank from the water supply valve. If it becomes lose, water would understandably trickle down from it to the floor. Fortunately, you can easily fix this by using your pipe wrench to tighten the nut. Start by giving it a 1/4 turn; if this fixes the leak, do not give it another turn. If the leak reduces but is still present, give the lock nut another 1/4 turn. This should stop the leak but, if it doesn’t, do not give the nut an additional turn since doing so will only damage it.

If tightening the locknut doesn’t work, it may have to be replaced along with the toilet fill valve (i.e. the valve in the tank that holds the supply hose from the main supply valve in place).

Leak Caused by Tank Bolts

Your tank is connected to the toilet bowl through a set of bolts, nuts, and washers, which can cause a leak if they’re damaged or misaligned. You can tell that the leak is coming from the bolts since water droplets will be present on them. Tightening the bolts should fix the problem but, if it doesn’t, you’ll have to replace them with new ones along with new nuts and washers.

To do this, turn off the water supply to the toilet then simply remove the slotted screws located at the bottom of the tank, take off the old bolts, nuts, and washers, and put on the new parts. Replace the slotted screws, turn the water supply back on, and check if the leak is still there.

Explore these solutions now to stop your toilet tank from leaking onto the floor.

Water Heater Overflow Valve Leaking: What to Do

If you have a water heater, you probably already know that it comes with an overflow valve. This valve, which is also known as the temperature and pressure relief valve or simply the relief valve, is important since it helps relieve pressure from the water heater. Remember: water expands when it’s heated, which means the pressure in your machine is high as it heats your bathwater. If this pressure has nowhere to go, it will eventually cause your water heater to explode.

The problem with overflow valves is that it’s hard to determine whether they’re leaking or not since they’re supposed to release some amount of water. After all, it’s their job to discharge some water from the water heater to relieve the pressure. So how would you know if the valve is just doing what it’s supposed to or if it’s already leaking? This guide can help you answer this question.

Find Out Where The Leak Is

If the overflow valve has released a small amount of water at one time, it probably is just doing its job and there’s no need for you to worry. But, if the valve continually drips out a slow leak, or if it releases a large amount of water in a sporadic pattern, then there definitely is a problem. Of course, if the leak is coming from the threads where the valve has been screwed on the water heater, these threads have to be fixed ASAP.

If The Leak Is From The Surrounding Area

As mentioned above, the leak from your overflow valve may come from the threads that it’s attached to and not from the valve itself. In this case, fixing it is easy since you only need to turn off the water heater, unscrew the overflow valve, apply plumbers’ pipe compound on the threads, and reattach the valve.

If The Leak Is From The Valve Itself

If the overflow valve sporadically lets out a large amount of water, the problem usually lies with the water heater’s thermostat. More likely than not, the thermostat has caused the temperature in the heater to rise to abnormal levels, causing the pressure inside to rise and making it necessary for the valve to let out water more often and in large quantities. You can solve this problem by replacing the faulty thermostat with a new one.

If the overflow valve slowly leaks out a small amount of water, the problem is usually the valve itself, which has become either too old or damaged. The best step to take is to replace the valve with a new one, which usually costs less than $20 and is easy to install. Simply drain some water from the heater, take out the discharge tube, remove the old valve, put in the new one, and reattach the discharge tube.

Take note that the problem may not stop at replacing the overflow valve. Even if the valve is new, it could still leak if you have a “closed system”; that is, the expanding hot water cannot flow back to the main water supply and has nowhere else to go. If this is the case, you’ll need to install an expansion tank, which will accommodate extra water from your heater and prevent it from leaking out through the overflow valve.

Sprinkler Head Leaking: How to Fix It

Having a leaking sprinkler head can be annoying. For one thing, it can cause your lawn to be unevenly watered and affect how the grass grows. Of course, it causes you to waste a large amount of water, which can lead not only to the degradation of Mother Nature but also to impossibly large water bills.

Fortunately, fixing this problem isn’t as difficult as it may seem. You can start looking for the right solution by using this guide.

Determine What Causes The Leak

A leaking sprinkler head can be caused by several things. It may be caused by low head drainage, which isn’t actually a type of leak but is a problem that develops if your sprinkler system is installed in a sloped area. You can tell if you have a low head drainage problem when the lowest sprinklers release water after you’ve turned off the system. This flow always stops when the pipes are fully drained of water.

If the sprinkler leaks 24/7, it most likely is a leak in the sprinkler head and other parts. You can usually tell that it’s a leak (and not low head damage) because the area near the sprinklers have moss or algae growing on it as well as puddles of water that never really dry out.

Fix The Leak

If your sprinkler system has low head drainage, you can easily fix it by installing anti-drain check valves in the sprinkler heads. These valves are specially designed to automatically close when the water supply is turned off and prevent water from draining through the lowest sprinkler heads.

If you’ve confirmed that you do have a leak in your sprinkler head, take off the head to see if it’s damaged or clogged. Most sprinkler systems allow you to easily remove the head by twisting it off from the housing. There most likely is a seal at the bottom of the cap to keep water from leaking off; check this seal to see if it’s intact or if it has been damaged. If it’s the latter, you can replace it with a new seal, which you can usually buy from your local hardware shop.

Don’t forget to check if the sprinkler head. Take out the filter and flush it out with water to dislodge any debris that may have been stuck in it. You should also inspect the sprinkler head itself to see if any debris are lodged in it or if its threads (located at the bottom of the housing) are damaged. If it’s either of the two, you’ll need to replace the sprinkler head with a new one.

Of course, take note that leaks may appear to be in the sprinkler head but may actually originate from the riser or the fitting. If the leak originates from the latter, you’ll need to replace the fitting ASAP. If the leak comes from the riser, turn off the water supply, remove the riser, and check it for any damage. If it’s in good condition, wrap Teflon tape around its threads then reattach it to the fitting, turn the water back on, and see if the leak is still there.

Take these steps now to fix the leak in your sprinkler head!

Toilet Tank Leaking At Bolts: Tips for Repairing It

Many houses have a two-piece toilet, which is composed of two parts: the bowl (which is what people sit on) and the tank (which stores water that will flush the toilet). These two parts are connected to each other through a set of bolts, which pass through holes at the bottom the tank and a matching set of holes in the ridge of the bowl. These bolts usually won’t cause problems but, if they’re improperly installed or are damaged, they can lead to serious leaking.

Leaking bolts are usually identified by the presence of water droplets on their ends. Slow leaks can also be noticed since there would be water on the floor under the tank. If you suspect that your toilet tank is leaking at the bolts, you can take the following steps:

Inspect The Bolts and Other Parts

The first thing you should do is to check if the bolts are properly installed. They should be properly and equally tightened; if they’re not, this can cause the leak. Tighten the bolts if you see that they’re too loose.

Don’t forget to check the rubber washers, too. These parts can degrade as time goes by, so they may already be damaged if it’s been years since you replaced them or if you haven’t replaced them at all.

Take a Close Look at the Tank

Sometimes, the problem lies not with the bolts themselves but with the toilet tank. One scenario is when there’s a crack or several cracks around the bolt hole. If this is the case, you will always have a leak even if you’d replace the bolts or rubber washers, and you’ll need to replace the tank. Take note that even a hairline crack around the bolt hole can already cause a significant leak due to water pressure.

You should also ensure that the tank sits on the ridge of the bowl. Proper placement of the tank is usually needed to create the right amount of water pressure that will compress the rubber washers and make a seal against leaks.

Replace the Bolts, Nuts, Washers

If you’ve checked the bolts, nuts, or rubber washers and found out that they are defective, you’ll need to replace them to stop the leaking. Even if only one of them was defective, it’s a good idea to replace all the parts at the same time so you can deal with the problem all at once instead of having to go through the process several times. You can start by taking these steps:

1. Purchase the correct parts from the hardware store. Check your toilet’s manual to know the exact model numbers of the parts you need to buy.

2. Turn off the water supply to the toilet.

3. Flush the toilet to remove the water that’s stored in the tank, and use a sponge to remove the remaining water in the tank.

4. Remove the tank lid and set it aside in a safe place.

5. Remove the slotted screws at the bottom of the tank. Depending on your toilet, you can either do this by hand or use an adjustable wrench to do so.

6. Take out the old bolts, nuts and washers. Take note of their position so you can install the new ones the right way. You may need to use a hacksaw blade or even a drill if the bolts won’t easily unscrew, but be careful when using these equipment to avoid damaging the tank.

7. Install the new bolts, nuts, and washers. Return the slotted screws and put the toilet lid back on.

8. Turn on the water shutoff valve to let water into the tank. Check for any leaks and tighten the nuts as necessary.

Use these tips now to stop the leaking from the bolts of your toilet tank.

Delta Shower Head Leaking and How to Fix It

Shower head leaks should be costly when not properly monitored over time. There are more than one reason for this dilemma, but you should be able to fix this yourself. There is no need to call the plumber just yet. In fact, the solution could only be a lot simpler than you think. One of the most common culprits is the clogged shower head holes. Here are simple steps to deal with shower head leaks.

1. Turn Off Water Supply

The most efficient way to handle this type of repair is to turn off the water supply going to the shower head. This will ensure that you won’t waste too much water when performing this task.

2. Remove the Faceplate of the Shower Head

It is essential to remove the shower head faceplate from the shower fixture. Begin by just unscrewing the faceplate only. Some shower fixture have screws that you can twist to loosen the assembly. Other models require you to simply twist the faceplate without the screws.

3. Immerse the Shower Head or Faceplate in White Vinegar

Use a container or basin to dip the faceplate assembly into it. Make sure that you have mixed the vinegar solution before immersing the shower component in it for eight long hours. Basically, the purpose is to dissolve any mineral deposits or buildups from the water supply.

4. Remove Excess Deposits After Dipping in Vinegar

After the immersion, you can now notice the difference. Try to check if the major dirt and other deposits have been gone. You can use toothpick or tiny nail to pick the holes of the shower head. You will be able to notice that the major buildup of dirt has been eliminated so you can now scrub the faceplate clean with the use of a stiff plastic scrub.

5. Check for Leaks in the Shower Head After Cleaning

You can determine if the unclogging procedure had worked by checking the shower head holes. You can now reattach the shower head or the faceplate back onto the fixture. Then, after you have determined that the problem has subsided, you need to turn the water supply back on. If you think that this procedure has solved your dilemma, then you should be happy as you have solved it. Otherwise, you need to look for other reasons why your shower head keeps on leaking. For this reason, you have to try something else.

Worn Out Rubber Washer

Sometimes, the only culprit is the worn out rubber washer inside the shower head. Therefore, you only have to replace this material that you can purchase over at the hardware store. For Delta faucets, you need to visit the supplier for this problem to be resolved.

Damaged Diverter Valve

Other issues also involve worn out diverter valve. When this happens, you can just clean it up or you have to replace it depending on the situation. If it has malfunctioned, then surely it should be replaced with Delta parts to achieve the best results. Otherwise, the problem will still linger.

Delta Bathroom Faucet Leaking and Tips for Fixing It

There are many issues at home and one of the most common is dripping faucets. This type of problem can be solved by replacing the rubber seat and spring. Delta bathroom faucet leaks can be solved with careful analysis of the situation.

Tools Necessary for Handling Faucet Repairs

One of the basic requirements when handling faucet repairs is the use of certain tools. Such will include a pair of pliers, Allen wrench or screwdriver, new rubber seating and spring, stem grease, and a new stem if necessary.

Stem Needs to be Replaced Whenever Necessary

  • If you noticed that the handle is already stiff when you try to turn on the faucet, then you should decide to replace the stem.
  • Likewise, if you have seen that there are leaks around the handle whenever you open the faucet.
  • Certain leaks won’t stop even after the seat and spring have been replaced.

Steps to Follow when Deciding to Repair the Leaky Faucet

1. Remove the Handle
Even how experienced you are, you simply have to turn off the water supply every time you encounter repairs, particularly when it comes to plumbing issues.

You can remove the handle after, by simply using an Allen key on the side of the handle or just by unscrewing it.

2. Remove the Bonnet Nut
You will have to remove the bonnet nut after removing the handle holding the stem. The seat and spring should be under the stem, so you must have to remove it. Pliers can be used to remove this or you can use a crescent wrench to unscrew it and pull it up.

3. Remove the Stem
The stem can be removed so that you can access the seat and spring. This set should be replaced by removing first the stem with a pair of pliers. Just don’t lose sight of the exact location of the stem as it will be useful when you ought to reinstall a new one later on.

4. Removing the Seat and Spring
After removing the stem, you can look inside the opening of the faucet handle for the location of the stem. You can also see the rubber seat and spring below the opening. You can remove this by simply putting a tiny screwdriver or an Allen key to pull it up.

5. Installing a New Seat and Spring
The rubber seat should be put on top the new spring. Take note of the arrangement as it should be lined up just like the previous installation. Use a screwdriver or Allen wrench.

6. Replacing the Stem
Put the stem back into place, but don’t forget to grease the O-ring from the stem base using stem grease. Gently install the stem by aligning the tabs on the stem of the body slots. Ensure that you have pushed it down to replace the bonnet nut. Reinstall the bonnet nut in place and use a pair of pliers to screw it back in.

7. Checking for Leaks
Check for some leaks before reinstalling the handle. After you determine the absence of leaks, then you can put the handle back on its position. Then, turn the water supply back on.