Shower Faucet Leaking from Handle: How to Fix It

A leaking shower faucet is a recipe for irritation and will hike your water and electricity bill in no time. The cause of the leak in your shower faucet could be as a result of worn inner seals, or the inner parts of your shower faucet have become corroded. Hard water deposits also cause the shower faucet to clog leading up to the shower faucet leaking.

The gaskets and the O-rubber rings used for sealing the connections between the moving metal parts will get worn with time. Water will leak from the wear in the parts. Do not over tighten the faucet least you do more harm than good. The steps bellow will guide you in repairing and fixing a leaky shower faucet.

1. First of all, if you use a two-handle faucet, feel the water dripping from the shower head if it is hot or cold. This will let you know which faucet has a problem. Turn off the water supply to the shower faucet and embark on disassembly.

2. Remove the handle first and depending on the model of your shower faucet, different methods can apply. The older and simple designs have an exposed screw at the center front of the faucet handle. Newer models come designed that the screw is not visible since it has a cover cap. Use a thin blade or flat head screwdriver to remove the cap and access the screw.

3. Wiggle the handle while being careful not to break it and remove it. Sometimes the corrosion and hard water deposits will make it a hard job of removing the faucet and so, use a faucet handle remover or improvise with a screwdriver.

4. Next, remove the sleeve and trim which fits over the faucet’s stem. For this task, you will need a plumber’s deep socket to remove the stem from the faucet’s body. Fit the deep socket over the hex nut and unscrew it in an anticlockwise direction.

5. Replace all the worn out o-rings, washers, flat washer, and the seals. Assemble the faucet stem and lubricate it with plumber’s grease. Place the stem into the faucet’s body and tighten it.

6. Test if the leak is over by temporarily placing the handle back on and turning on the water. The leak should be gone if all the components of the stem if you have linked the parts well together. Finish off the assembly and use tub caulk to seal the trim to the wall.

Invest in a faucet washer kit to ensure that the next time your shower faucet leaks, you will be well prepared when the leak pops again. The above procedure is replicable for different shower faucet brands.

Water Softener Leaking: Tips for Repairing It

The first thing you should do when you find your water softener leaking is turn off the power supply. You will be vulnerable to electric shocks and the appliance may get damaged, there is a possibility of partial short circuits as well. Complete or total circuit failures are rare these days since most homes or properties have more than one circuit breakers and the electrical wiring is phased.

1. Turn Water Off

To diagnose and to fix water softener leaking, you must turn the water supply off. You can easily access the shut off valve which is usually at the rear side of the unit. It should be visible. Some inlet valves allow for complete shut off while some systems allow you to get water in the tap but it would not go through the softener. There are bypass options in such softener models. Now, before you take any further steps there is one caveat you should be aware of. Not all water softener leaks are easy to diagnose and chances are high they would be beyond your technical expertise. Not everyone is an expert in water softeners anyway. In such cases, you would need to contact your provider. Call up the manufacturer or installer and get them to check the leak.

2. Check Pipes

It is possible that water softener leaking is due to a poorly connected pipe or faulty pipe. You need to check the installer after taking the aforementioned steps. Look at the inlet valve, the outlet valve, the condition of the pipe and look for signs of damage or wearing out. Wear and tear is common with old systems, not so with new ones. Damages pipes should be replaced. You cannot really repair them. If you still have the warranty, then you can get the pipe replaced without any charges. Beyond the warranty period, you will have to pay for it unless you have an annual maintenance contract.

3. Components

Water softener leaking can be due to the failure of one of the several components inside. The tank inside may overflow. There may be physical damages somewhere. The tank inside can get clogged. There can be more pressure than usual or what the unit is supposed to withstand and hence the relief valve may let the excess water flow down. This dripping will appear to be leaks and it can be concerning. Do not try to open the water softener unless you are aware of the potential problems. You may not understand much of the internal parts. Call your manufacturer or installer.

Garbage Disposal Leaking from Top and How to Fix It

Garbage disposal leaks are common and can be complicated if you don’t really know the cause of the leak. You need to have a measured response and it starts with knowing what can possibly be wrong or go wrong with your garbage disposal. Garbage disposal leaking from top can be due to worn out rings, clogging of multiple inlets, clogged outlets, damaged or debris laden connections and failing seals. Let us explore the various causes of garbage disposal leaking from top and how you can fix them.

Start With the Sink Flange.

The sink flange is the uppermost portion of the unit. The sink flange is where the unit is connected to the drain of the sink. This sink flange can cause a leak if the mounting bolts are loosened for some reason. Usually, there are three mounting bolts and you should tighten them to see if the leak persists. If it doesn’t then you are sorted and if it does then you need to look beyond the mounting bolts.

Plumber’s putty that is used to retain the tightened mounting bolts in their place can also be worn out which will cause leaks. You can apply a new coat of plumber’s putty between the pipe and the sink flange. For this, you should first uninstall the mounting bolts or loosen them, apply the putty and then tighten the bolts again to hold them and the putty in their rightful place.

Dishwashers and Other Appliances Connected to the Garbage Disposal Unit Can also Cause Leaks.

Multiple inlets will always complicate matters. The hose connecting the dishwasher to the garbage disposal may not be well clamped. You need to check if the clamp is secured enough. If not, then you should tighten the clamp. If the hose is cracked, then you should replace it.

The Discharge Pipe May be Damaged, Clogged or Worn Out.

The discharge pipe is responsible for a smooth transition of waste through the garbage disposal to the sink drain. Once you are sure that the seal and sink flange are in perfect condition, look for wear & tear or signs of damage in the discharge pipe. If you have to replace the discharge pipe, also replace the retaining nut and the seal.

Old Garbage Disposal Systems are Vulnerable to Cracking.

It could be the interior shell or the exterior and the unit may get too stained or clogged and hence rendered inefficient. You need to consider replacing the garbage disposal unit if it is too old.

Toilet Flapper Leaking and Tips for Fixing It

A toilet flapper is the rubber mechanism found in the tank of your toilet. In the flush valve, the flapper is the moving part. As it moves, it seals the water into the tank allowing the water to exit the tank during flushing. As with every moving part, the flapper also gets worn with continued use.

The first thing when you note a leak from your toilet’s tank is to establish the origin of the leak. Add a dye into the water in the tank give it a few minutes to dissolve. Check the toilet bowl, and if you find colored water, then you have a leaking flapper. You can also do it by yourself by following the steps below.

• Close the supply of water to your toilet. You will find the water inlet below the toilets tank behind the bowl.

• Check the beaded chain length from the flapper to the flush handle as you flush the water from the tank. This is to ensure you do not make it too short or long after you have replaced the flapper.

• Some manufacturers connect the flapper with a circular ring around the tube. Make sure you remove the refilling tube from the overflow tube to access the flapper.

• First, remove the beaded chain from the flush handle and slide the worn out flapper from the overflow tube to remove it. For the new toilet models, bend the flapper ears outwards and off the pins on the flush valve.

• Note the manufacturer and the toilet model number and take them with you when purchasing a new flapper. You can get the model number from the back inside of the tank and the manufacturer’s name near the hinge of the seat.

• After acquiring the new flapper, install it by sliding it over and down the overflow tube of the toilet until it reaches the bottom of the tank until it covers the center of the flush valve. For the new plastic valve models, cut off the places marked ‘cut’ and slip the ears of the new flapper over the pins of the flush valve.

A leaking flapper can waste over 200 gallons of liters in a single day inflating your water bill to more than you can imagine. Statistics show that leaky flapper can fill a standard sized swimming pool four times in a year, so you better have it fixed as soon as possible to avoid hefty water bills.

Tub Faucet Leaking and What to Do

The faucet of your tub can leak. At times, the leak will be miniscule facilitating a slow drip. This may even be unnoticeable for a while. If the drip is constant and perhaps audible, then you cannot miss it. Do not ignore mild drips simply because they are not concerning enough. You should not wait till the leak becomes severe. Milder drips are easier to fix. Whatever is the severity of tub faucet leaking, you can hire a plumber or you can attempt to fix it yourself. Here is a guide to fix tub faucet leaking without any professional help.

Causes of Tub Faucet Leaking

A tub faucet may leak due to damaged seals or worn out rubber washers, malfunctioning gaskets or a damaged valve assembly. You have to inspect the faucet, identify the problem and then replace the damaged part. If some screws or some parts are loosened then tightening them should solve the problem.

Get the Parts

You can do this preemptively or after you have inspected the problem. The bottom line is you need the new parts to replace the old parts when you get down to fix the leak. You can get all parts of a typical tub faucet, single handle or double handle, at your nearest hardware store. Make sure you get identical parts, preferably of the same manufacturer. Don’t go for compatible parts as they may not be perfect.

Get Started

The first step is to disassemble the faucet. Turn the water supply off, drain the water from the pipes through the faucet and then open the handle insert. Remove the screw of the handle, wiggle it and then pull it outward. Some handles are frozen or jammed and if you pull with enormous force then they may break. Use a hairdryer or some source of heat to make it easy. Different handles open differently. Some will just come straight off, some need to be turned clockwise, some require a bit of popping and some will have patches or specific maneuvers. Refer to the manufacturer’s handbook if you have one or check online.

You could also get to the escutcheon plate and take off the screws. Get to the stem bonnet and slide the bath socket, turn it anticlockwise and loosen the stem. Unscrew it and then remove it. You may need some lubricant if it is stuck. You can also use a seat wrench to remove the handle. This is the most demanding step of the job because handles get jammed, corroded and would stick to the rest of the installation.

You have to look for the real causes of the leak. Usually, there are two causes. The seat washer may be loose. The washers may be worn and torn or damaged. Years of use will almost definitely damage the washers and seats. You will have to replace these. Start by unscrewing the packing nut. You can easily twist the stem in a clockwise turn and then get it out of the bonnet. You can slide the packing washer out of the panel. To make it easier, use a screwdriver. You can also use some lubricant to make the steam slippery and easier to work on.

Get rid of the old washer and install the new washer. Make sure you grease the new washer before you install it. As you put back the bonnet and stem valve assembly, make sure they are all cleaned and greased. You can also add pipe joint compound to the threads of the bonnet threads before reinstalling them. Grease the splines, reinstall the escutcheon plate and finally the handle.

The job is not that difficult. You will need some time, effort and a host of tools including an adjustable wrench, utility knife, handle puller, bath socket wrench and seat wrench. You will need the replacement parts depending on the problem. Regardless of the cause of the tub faucet leaking you will need stem valve repair parts and plumber’s grease.

Complications of Tub Faucet Leaking

Getting rid of the handle may seem like a herculean task. Over the years, a handle can get too rigid, not to operate but to get rid of. Even if you succeed partially, you may not be able to efficiently remove all the parts. Such complications are very common and that is why many homeowners call in the plumbers. You may have trouble identifying the cause of the leak. The washers may seem fine, they may seem tightened enough and there may be no apparent signs of damage or wear & tear. These don’t imply that there is no leak. The cause is simply elusive. More trained eyes will be able to diagnose the problem. Again, you need plumbers to look for such specific problems. Should you be unsure of fixing tub faucet leaking, get professional help.

Water Heater Drain Valve Leaking and How to Fix It

If you find yourself dealing with a water heater drain valve leaking, you can wind up dealing with a myriad of problems. In many cases, the valve itself is the part of your water heater that is leaking. However, in other cases, it can wind up being the flange around your valve that is leaking. This is a particularly prevalent problem with your older water heaters.

Regardless of the specific problem, you don’t need to worry too much. More often than not, you can deal with the problem in a straightforward fashion.

How To Deal With A Water Heater Drain Valve Leaking

When it comes to dealing with your water heater drain valve leaking, your first option will be to tighten the valve. Capping your valve outlets is another possibility for dealing with small leaks. Finally, if all else fails, you can opt to have the drain valve for your water heater replaced entirely.

One of the annoying things about drain valves is their durability. The ones that come from the factories are made from plastic, and aren’t terribly durable. Flushing it out can wind up tightening it, which can prove to be an effective means of solving your problem. If this doesn’t work, you may need to drain the water heater, and replace the drain valve entirely. However, this is not your only solution. You can actually cap the whole thing, and call it a day more often than not.

If you do need to replace your water heater drain valve, don’t panic. This process is fairly straightforward. You will want to keep in mind that this project does require a certain measure of experience with home improvement projects. It will take you approximately an hour to complete this project.

In the end, replacement work isn’t your most likely outcome. Simply tightening the fittings on your drain valve can prove to be the most effective means of dealing with the problem. Also, as we mentioned before, capping your valve can also be a good way to take care of the more minor leaks. Replacement work can be handled by someone with an absolute minimum of handyperson experience. Nonetheless, in situations such as these, it is important to appreciate your limitations. When it comes to how to replace a water heater drain valve, you can’t really make the situation too much worse by making mistakes. However, if you don’t want to bother with the risk, then hire professional contractors to handle it.

Hot Tub Leaking from Bottom: How to Repair It

While a hot tub leaking from bottom is a serious problem, you don’t need to worry too much. You should deal with the problem as soon as possible, but it also seems unlikely that the problem involves your spa shell.

In most situations, you can deal with a hot tub leaking from the bottom easily enough. There are just a few simple things that you are going to want to keep in mind.

When Your Hot Tub Is Leaking From The Bottom

The first thing you are going to want to do is consider the most common types of hot tub leaks:

Leaky spa pumps: If your spa pump is leaking, the likely culprit can be shaft seals, unions, or wet end volutes.

Leaky spa lights: Loose/cracked lens can lead to leaks. Your light housing or niche is usually found on the same side as your spa pak, so it shouldn’t be too difficult at all to service your tub.

Leaky spa filter: Locking filter rings have sometimes just become a little too loosened, so you’ll just need to have them tightened up. In most cases, new gaskets or O-rings are going to be your best bet for dealing with the problem.

Leaky spa plumbing: Occasionally, you can find yourself dealing with leaks in your PVC pipe. You can also find leaks alongside the backsides of spa jets. Loose locknuts are another potential problem to keep in mind. Finally, you could find yourself dealing with disintegrating spa jet gaskets. Spa plumbing leaks are particularly common at the glue joint areas.

Finding a specific leak can be challenging. You will want to perform visual inspections of the pump, the union fittings, the heater, the valves, the connections, and the shell. If you find the leak in any of these places, the work involved can vary from one aspect of the tub to another. For example, if the culprit is the pump, you may need to replace the pump seal. In many cases, you will need to have the pump replaced entirely. Union fittings can become loosened rather easily. If the union fittings are responsible for causing the leaks, having the fittings tightened is more often than not going to be the best bet.

You can also put trace amounts of food coloring in your water. Watch where the water leaks to. This is a good way to figure out where the leak is coming from, if you can’t visually detect anything.

Basement Leaking Where Wall Meets Floor: Tips for Fixing It

When it comes to basement leaking where wall meets floor, we are talking about the cove. This is the area in which the basement floor of your home meets the wall. Due to the way your home is built, this area can become significantly prone to water penetration and leaking, as time goes on.

Thankfully, when it comes to dealing with basement cove leaks, you have solutions in place.

Dealing With Leaks Where The Wall Meets The Floor

Generally, when basements are built, concrete footers are poured and left to dry. Your walls are then established atop your footers. In the final stage, basement floors are poured atop the edges of footers, going against the walls of the basements. When your foundation goes through temperature/seasonal changes, all of these levels take punishment. All of them deal with this punishment in profoundly different ways.

With poor drainage or a clogged up footer drain, water from a rainstorm or underground spring can cause your water table to rise up your soil. This can go beyond the floor of your basement. Hydrostatic pressures will then force the water in throughout cracks/holes in your masonry joints. These cracks are of course formed by foundation elements expanding and contracting. At this point, you’re going to find yourself dealing with water in the cove area.

Relieving the water pressure from its underground source is a good solution. Installing footer drain tile systems can help you by draining away the water that is giving you a hard time. An outside footer drain can provide you with the best outcome possible. All of the outside soil should be excavated away from the perimeter of your home. You are also going to find that this approach is highly dependent upon having the proper elevations for your property. This can involve contacting engineers or surveyors. Using a drywell is generally not suggested, because it can be filled up with groundwater before the same happens to your basement. This can make everything even worse.

An interior drain tile is another possibility that you can explore. This method is considerably more straightforward, in addition to being less problematic. Trenches cut through your concrete floor around your basement perimeters is just the beginning. Hollow block walls will then drain the waters resting in your hollow cores. Sealing the interior walls, you can now re-cement your floor back to the original condition.

As you can see, there are obviously options to help you deal with the problem.

Water Heater Leaking from Drain Valve: What to Do

Leaking around water tanks are a part of life. Knowing how to do quick fixes and repairs can save you a fortune when it comes to home maintenance. If you think you have a leak in your hot water heater, check to see if it is something you can fix yourself.

The only time your water heater should be releasing water is when you open the valve to drain your tank. If you find that water is coming out of your tank on its own, the problem may not be too serious. Often times your water heater tank may be moved a bit and the valve can come loose that way. This kind of fix is easy and just require some tightening around the valve.

Leaking from the Valve

Before taking any action, you should be sure that the leak itself is actually coming from the valve. Take a cloth or towel and stick it underneath your valve. If it comes out wet, you know that the drain valve is where the leak is coming from. For a leaking valve, get an adjustable wrench and tighten the washer. This should solve your problem, but if your valve is still leaking, you may need to call a plumber.

Replacing the Drain Valve

If you notice that the valve itself is dry, your leak is most likely coming out from underneath the water heater. This can be fixed by removing the drain valve and replacing it. You will need to empty your hot water tank completely before attempting to remove the drain valve. Purchase a drain valve repair kit for your local home repair store and follow the instruction to install your new valve.

Replacing the Washer in the Drain Valve

A hot water heater leak by the drain valve may also be caused by a worn out washer. Check to see if the drain valve washer needs to be replaced by unscrewing and see if it tightens any further. Replacing the washer should fix your leaky valve, but if it doesn’t you may have a more serious problem.

Sometimes the hot water heater tank itself will get corroded throughout the body of the tank. This corrosion will cause tears and holes to form in the walls of the tank. If you see anything like this on your hot water heater, you will need to get it replaced as soon as possible. Call your plumber and drain out your tank to prevent any more leaking.

Water Heater Leaking from Relief Valve: How to Fix It

Before you can remedy any problem, you ought to know the real cause. Water heater leaking from relief valve is a very common problem. You should know that every water heater has a relief valve, also known as temperature & pressure relief valve. This valve is supposed to let steam or water out when the temperature of the water rises to 210 degrees and the pressure reaches 150 psi. There are some water heaters that may have different temperature and pressure thresholds.

The moment you find water dripping down the water heater or sprinkling out, you should be cautious but don’t panic. Here are the steps you can take when you see water heater leaking from relief valve.

Check the relief valve and see if it is installed properly.

You also need to make sure you have the right kind of relief valve. You cannot use a boiler relief valve in a contemporary water heater. You cannot use a valve that doesn’t fit the model or design. You should have the valve that your manufacturer or the brand of the water heater has recommended. If the valve is not identical or it is damaged, then you should get it replaced. A wrong valve or a damaged valve may even leak water at 30 psi which is insignificant compared to 150 psi.

Even if you are unsure whether or not the valve is damaged, it is not unwise to replace it.

Do not replace the original valve unless you are certain. But if you have replaced the valve in the past, then spending another fifteen bucks or so to get a new valve should not trouble you. If you are completely unaware of how to replace the valve, it is better to hire a plumber.

It is quite possible that the relief valve is perfectly in order and either the temperature or the pressure is causing the leak.

Get a thermometer and measure the temperature of the water. Turn on the faucet, collect some hot water and insert the thermometer to get an accurate measurement. If it is close to or exceeding 200 degrees then you should turn down the temperature setting by a few notches. You should ideally go for 120 degrees and at the most 150 degrees. Humans don’t need water to be that hot. You would also be using more energy.

If the temperature is optimum then it may be the pressure.

Get a garden hose, connect a pressure gauge, fix it to the faucet and let the water drain out to the tub, bucket or outside. You will get the reading. Try to stay within 40 psi to 80 psi.