GE Profile Washing Machine Troubleshooting

GE makes some of the best washing machines in the world. They are durable, reliable, efficient and reasonably priced. Washing machines are sturdy appliances and are not always taken care of. Lack of maintenance and prolonging repairs can lead to uncertain and expected problems. Not only should you be proactive with your maintenance but you must also use a GE profile washing machine as per the recommendations. Here are some GE profile washing machine troubleshooting tips that will come handy when the problems emerge.

Washer Does Not Fill

You will have sporadic scenarios when the washer will not fill. Water flow is the main cause of concern here. No washing machine is immune to this problem and GE is no exception. Begin the diagnosis by checking the washer, the cold and hot faucets and ensure they are fully turned on, check the water pressure as GE washing machines usually require anywhere from 10 to 120 pounds per square inch of water pressure. Inspect the fill hoses and look for blockage or clogs. See if there are any kinks in the hoses. You may have to replace the hoses if they are kinked or clogged beyond repair and cleaning. Also inspect the filter screen in the hoses. You can clean these with a toothpick or brush.

Check the Lid

If you are having any problem in the cycle, then check the lid. Usually this problem occurs when the lid is not properly closed. Any kind of hard or rigid substance can prevent the lid from closing properly. You might have issues with the washer wherein it would not spin or drain properly or agitate to handle the load. Imbalanced load could be an issue here. There is a simple solution here. Just redistribute the load.

Leaking Washing Machine

If you have leaks in your GE profile washing machine, then it could be due to leaks around the washer door. The door gasket may be damaged. There could be debris or dirt clogging the door and leading to vents or tiny gaps. A leaking washer may be an issue and you should check the drainage hose. Suds can also be the main cause. Using less amount of detergent when you have such issues would be helpful. Excessive use of detergent will unnecessarily lead to more suds and debris.

Always run the self diagnostic checks of GE washing machines, have the instruction manual or user handbook with you and be ready with the tools you need to check the various components.

Hotpoint Washing Machine Troubleshooting

There is nothing more aggravating than to fill your washing machine only to find it won’t start, or worse, find that it is still full of water at the end of a cycle. Calling a repairman can be quite expensive. We have curated a list of common, easy-to-fix problems with Hotpoint washing machines. This will help you decide if a service call is required.

Washer is Leaking Water

The first thing you will want to check is the main plumbing coming into your home. If all seems okay there, check the fill hoses and drain hose for any visible leaks.

Occasionally, if the washer was not leveled properly during installation leaks may occur. This can easily be adjusted by the feet on the front of the washer.

Washer Will Not Spin

There could be a few possible causes why your washer won’t spin. Many times, it is due to the safety latch on the door. If it did not shut all the way and the latch did not engage, washer will not function properly. Try re-closing the lid to see if this helps.

Another common reason is the load becomes unbalanced and clothes need to be distributed evenly. Most models do have sensors that try to correct this and balance itself, but sometimes it must be done by hand.

Damage to the drive belt or pulleys will also prevent the machine from spinning. Inspect the belt and pulleys for visible wear, cracks or breaks. Replace if needed.

Washer Will Not Drain

If you are having trouble with your washer draining you should check the drain hose first, any kinks or blockage could prevent the tub from emptying properly.

Next, you will need to inspect your drain pump. It is not uncommon for small pieces of clothing, socks or other debris to get caught in the pump. Pump must be removed and checked for any blockages.

Common Error Codes

F01- Electronic circuit board failure. It is recommended to unplug from the power source, wait two minutes, then plug back in. Codes should clear, if not, may require a service call.
F02- Motor circuit failure
F03- Temperature sensor failure
F05- Drain blockage or pump issue
F06- Door lock failure
F07- Electronic circuit board or heating circuit failure
F08- Heater failure
F09- Software failure
F11- Pump circuit failure
F12- Electronic control failure
F16- Drum lock position sensor failure
F18- Internal data error

Don’t despair if you find your Hotpoint washing machine not working. Many times the issue can be solved with simple troubleshooting.

Hobart Dishwasher Troubleshooting

Hobart dishwasher has many generic problems and some specific to the models. Not that these dishwashers are unique or that their problems are any different from dishwashers made by other companies but the approach to troubleshooting is not always identical. Here is a comprehensive Hobart dishwasher troubleshooting guide that will shed light on common problems.

Machine Not Running

If the machine doesn’t start or doesn’t run then check the power source, you could have a tripped circuit break or the fuse has blow out. The water level in the tank could also be the power. Check the power in the socket and also check the plug. Do not use faulty extensions and don’t opt for any plugs or components that are not recommended by Hobart.

Dishes Still Dirty

If you are unhappy with the cleanliness of the dishes then you need to check the drainage. The dirty water needs to be drained completely. Clogged drain or any kind of blockage will prevent this and that will lead to dirty or unclean dishes. A damaged or worn out O-ring can prevent the drain from closing properly. Check the pressure of the water. There may be some obstruction in the pump.

Fluctuations in temperature or inaccurate water temperature may lead to unclean dishes, so can inappropriate choice of detergent and excessive deposits of minerals through the rinse system. You will have to get rid of the lime and in some cases call in the technician to replace a few worn out components. Dishes may be unclean due to many reasons, from lack of maintenance to clogged strainers, obstructions in the wash arms, clogged detergent dispenser, excessive soiling on the dishes, poor loading technique and limited or lack of water supply.

Spots on Dishes

Most dishwashers would have a spotting problem, especially with glasses and silverware as well as with dishes. Poorly loaded racks, inadequate temperature of rinse water, poor water pressure, hard water, excessive use of detergent or additive and sanitizer, excessive soiling and stains on the wares can cause spotting. One or more of these reasons may apply in any given scenario. You need to identify the exact problem and respond accordingly.

Error Code: EE

When you have the error code EE displayed on a Hobart dishwasher indicating there is a problem with the temperature of the rinse water, you must attend to the dirty line strainer, the remove strainer cap and clean them all to get rid of any blockage or clogging that you find. Check the water pressure of the supply line, look for mineral deposits and check the incoming water temperature.

Electric Water Heater Troubleshooting No Hot Water

It can be very frustrating to turn on the faucet, only to find out you have no hot water. Before calling a repairman, there are some common problems you can investigate on your own. We have compiled a list of tips to help you resolve any issues you are having with your electric hot water heater.

Check the Power Source

The easiest and most obvious place to start is with your power source. You will want to check the breaker to make sure it has not tripped or become weak over time. There is also a reset button on the heating elements that can trip as well. If it happens to be either one of these, it’s probable you have a bigger problem on your hands. Most likely, the element has grounded and is creating an electrical short.

You may also check the supply wires for any damage. These wires are located in the upper access panel and normally protected by foam and insulation. You should shut off the power to the hot water heater before handling wiring.

Check the Upper Element

If you have no hot water at all, you will need to check the upper element. It is very important to shut off the power to the appliance before attempting this step. Carefully remove the insulation, using gloves and googles is recommended as some of this material may contain fiberglass.

Using a voltage meter, check the wires attached to the element and to the thermostat to see if electricity is present. Next, loosen the two screws on the heating element and remove the wires. Set the resistance on your meter to 1,000, placing probes on screws. Depending on your appliance, a 3,500-watt element should read 16 ohms; a 4,500-watt element should read 12 – 13 ohms; a 5,500- watt element should read 10 -11 ohms. If the element does not register on the voltage meter it will need to be replaced.

Check the Thermostat

Normally, you will find your hot water heater has two elements and two thermostats. Start by turning upper element to its highest temperature setting. Check the #1 and #2 terminals with a hot water heater tester to make sure the contacts are active. If the tester does not react, the thermostat is not working and will need to be replaced.

Anytime you are dealing with electrical appliances, use extreme caution. You will need to have knowledge of how to use multimeter to complete the steps mentioned in this article.

Electric Water Heater Thermostat Troubleshooting

Electric water heaters will have some problems from time to time. You can expect some thermostat related problems after a few years of everyday use. Thermostats are the regulators that will control the temperature of the water. Some thermostats can be used to set hot, hotter, hottest temperatures. Some thermostats allow you to set an exact temperature using its digital interface. Regardless of the nature of the interface and the type of electric water heater you have, there will be heating problems. The water heater may not heat the water at all, it may heat mildly or it may heat too much.

Remember a few things before you try to troubleshoot a thermostat. When you check different components of an electric water heater, you do so after turning off the power. You cannot inspect a thermostat with the power turned off. Hence, make sure you don’t touch any exposed element or powered component of the electric water heater. You would get a shock. Some shocks can be fatal.

Common Causes

Whenever there are heating problems, they could be due to one of the many components including heating elements or it could be due to the thermostat. You should check the voltage of the heating elements. You can do this using a test lead connected to each of the wire terminals. Of course you should check one terminal at a time. When the water is hot inside the tank, there must not be any voltage. Wait for the water to get heated up if you have just turned on the power. If after the water is heated the elements remain hot then you should replace them. You may have to replace one or both the thermostats depending on your observation.

What to Do

You should check the lower thermostat when the tank inside has hot water. The reading should be 240V. If there is another reading then the upper thermostat must be replaced. Turn on the faucet for the bathtub or allow the hot water to flow out and check the lower heating element. If it doesn’t come on the lower thermostat then you need to replace the same. When the temperature of the water dips or when the hot water flows out, the lower thermostat will shut off and you would observe the upper thermostat turning on the upper heater. Now check the upper heating element and observe the voltage. If you witness the upper heating element doesn’t come on then you ought to replace the upper thermostat.

Bosch Washing Machine Troubleshooting

Bosch washing machine troubleshooting can be very simple, as easy as replacing a component or just cleaning some clogging, or it could be a daunting challenge demanding the intervention of a technician. Whatever is your scenario, you ought to cater to standard maintenance during Bosch washing machine troubleshooting. Timely maintenance can avert most of the common problems and can also enhance durability, reliability and performance of the appliance. Here are some standard maintenance steps you must take during Bosch washing machine troubleshooting.

Inspect the Hoses

Start with an inspection of the hoses. Look for the water hoses and check for any sign that implies weakness. You should inspect the hoses at least once in two months or so. The hoses may have some cracks, there could be blisters or they may be obviously damaged. Don’t wait for a leaking hose or a burst hose. Check the hoses when time is on your side. Always opt for recommended hoses while replacing the old ones.

Look for Water Damage

You should try and prevent flood damage and there are two easy ways to do this. You can opt for Water Shutoff System that will shut off the flow of water whenever there is any malfunction and Washing Machine Overflow Pan which will let all the water from drips and leaks to accumulate safely without causing a larger problem. This comes with a drain line attachment to naturally get rid of excess water buildup.

Overloading of Machine

Never overload a Bosch washing machine, do not let the level be affected by any external or internal problem, always ensure that the appliance is working optimally without any unpleasant noise or problem, ensure adequate power supply and don’t let the appliance be affected by voltage fluctuations if it is an issue in your area and finally use the right amount of the recommended detergent. Over time, water and detergent will lead to some degradation of the interiors. You should clean the inside of the appliance and do so at least once a month if you are a heavy user. Infrequent users can attend to such cleaning once in three months or so. Do not allow the buildup of detergent, unclean water and fabric softener. Fabric softener, lime buildup and harsh detergents are three most recurring threats to a washing machine.

There is a Bosch washing machine troubleshooting guide in the user manual. All error codes and potential problems along with their solutions are stated in the booklet. Study it before you take any step.

Whirlpool Cabrio Washing Machine Troubleshooting

Whirlpool has a handy guide for troubleshooting the Cabrio washing machine. There are more than two dozen models of Whirlpool Cabrio washing machines. Many look similar and even perform in an identical way but there are differences. What is not different is the set of codes, most of which apply to all the variants of Carbio washing machine.

Every time you have a problem with your Cabrio, you must be sure that the problem actually exists and that the machine is not mistakenly displaying an error. You should get rid of old error codes. To do this you must put the machine through the automatic diagnostic cycle. Check the code and then take the necessary steps. Now, let us go through the various codes, what they mean and what you can do.

Error LF
LF means the washing machine is taking longer than usual to fill. The stored error code for the same is F30. When this code appears, you must check the water inlet hoses, the valve screens, water faucets, drain hose, drain pipe, pressure switch and flood stop water supply hoses if you have them. Inlet hoses could be clogged or kinked, valve screens could be dirty, water faucets may be turned off, the hoses could be closed inside, the drain pipe may have the drain hose stick farther inside than it should or the pressure switch could be punctured, disconnected or kinked. Attending to the problem you find should solve the problem.

Error Ld
Ld means the washing machine is taking longer than usual to drain the water from the washtub. The stored error code for the same is F32. You should check the pump and drain hose to see if they are clogged, the drain hose should be at a height of at least five feet so it can conveniently reach the drainpipe without impairing the outflow of water, the drain pump needs to be checked to see if it is working properly, the pressure transducer hose should be diagnosed to find any punctures or connection problems.

Error uL
Error uL means there is an unbalance load. This is not a very complicated problem. All you need to do is redistribute the load, close the lid and then start the machine again. Usually, the imbalanced load will be flagged at the end of the wash cycle but before the final spin. When you don’t actually have any load issues but the machine displays the error nevertheless, you need to diagnose the suspension. Check the suspension spring rod kit. If it has gone kaput or has worn out then get a Cabrio Suspension Repair Kit for replacement.

Error oL
Error oL indicated overloading. The stored error code for the same is F70. This may be a harmless and unintended human error. Simply take out a few of your stuff, add detergent and water, close the lid and start the machine. If you don’t have enough clothes to overload the Cabrio, then there could be something wrong with the inner tub which may be jammed, there may be a rusted drive shaft or there can be something as humble as a sock clogged between the outer and inner baskets. Remove the sock, lubricate the shaft and check what’s jamming the inner tub.

Error Sd
Sd is the error shown when the machine detects suds. The stored error code for the same is F71. This could happen if you use normal detergents in your Cabrio. Whirlpool recommends you use only high efficiency detergent. Using too much detergent would also cause this problem because excessive suds would be the inevitable fallout. You should carry out the suds correction routine to solve this problem. Do not attempt to avoid the error as it is detrimental for the machine and your clothes would be poorly cleaned. They would get stained with suds.

Error lid
Error lid is obviously an indication of an opened lid. The stored error code for this is F81. If the lid is open, close it. With the lid open longer than ten minutes, the water inside the washing machine or the washtub to be precise should start drain out.

Error Po
Po is an error code indicating pump out while lid opened. As the washtub gets drained when your lid is open for ten minutes or more, you should close the lid to prevent the draining.

Error HC
HC indicates the switching of hot and cold hoses. This may happen if the temperature sensor is not working properly or at the end of a wash cycle to imply the cold and hot water inlet hoses have reversed. There may also be a problem with the water valve or the main control board.

Error dL
Error dL implies the lid or the door cannot be locked. The stored error codes for this are F80, F82, F84 and F85. Check if there is anything that is preventing the door or lid to be locked. It could be fabric, fabric softener or soap.

Maytag Dishwasher Repair Troubleshooting

There are some common and rare problems you would encounter with your Maytag dishwasher. You can call in the repairing specialist or you can attempt troubleshooting using the manual. Some problems are very easy to resolve. The common problems with Maytag dishwasher are poor quality of wash, no power or the motor failing to start, the washtub failing to fill, running motor, draining issues, noisy operation and water leak among others. Let us discuss these common issues in our Maytag dishwasher repair troubleshooting guide.

Poor quality of wash is primarily owing to food left on the dishes causing an etching, film or spotting. Do not ever place dishes, pots and pans with leftover food inside the dishwasher. Always get rid of solid and liquid food. Else, you would have stains or some kind of unpleasant texture on the dishes. Dishwashers are meant to clean stains, spots and other smudged debris from dishes, not actual solid food that will anyway go helter-skelter inside the tub when the water with the detergent weave the magic.

No Power

If you don’t have any power on your Maytag dishwasher or the motor will not start, check the fuse or circuit breaker. Check the socket to be sure it has power. Check the plug and the wire. Check extensions if you are using one. Confirm the door locking lever is completely closed. Be sure there is no defective door switch as that would prevent the appliance from starting. The motor could be locked or jammed due to some reason which may be the reason behind its malfunctioning or not running. The pump could also be at fault. Check these components and repair or replace them as needed. You may want to call in a technician if there are too many issues.

Washtub Fails

If the washtub fails to get filled then it is mostly likely a clogged water valve or defective water valve solenoid at the root of the problem. Clean the strainer screen. Check the solenoid to ensure continuity. Replace the valve if needed.

No Draining

A running motor but no draining is usually caused due to poor washes. Severe spotting is the real cause. Attend to all kinds of clogging as a result of severe spotting. The drain pump impeller may get clogged too. Likewise, any kind of blockage or locking at the motor would prevent it from starting and running, despite the tub filling up. Get rid of clogs. Noisy operation is usually due to rust, broken glass and other hard debris getting into the impeller and even the spray arms. Worn out or damaged components may also make the noise.

Kenmore Elite Front Load Washer Troubleshooting

Having trouble with your Kenmore Elite Front Load Washer? Before you call the repairman, we have some tips for troubleshooting common error codes to hopefully save you precious time and money.

1. Error Code F06
This error code points to an issue with the drive motor. If this occurs mid-spin the door will automatically lock for a few minutes. The usual culprit is when the motor tachometer cannot detect the washer speed. You must remove the back panel and check the wiring harness between the drive motor and the control board. If this seems to be okay, you should check the resistance of the motor windings. If any of the windings appear to be open, the drive motor is likely bad and will need to be replaced.

2. Error Code F11
This error code pops up when the machine has some type of communication issue. The most common cause is when one of the wiring harnesses going to the control panel works its way loose. You can check this by removing the top of the washer and checking all connections. You will also want to check the door latch to make sure it is catching and closing properly. Occasionally, you will receive this code due to machine control board failure.

3. Error Code F dl
This error code occurs when there is an issue with the door latch. It will attempt to lock or unlock the latch six times before the code pops up. This can indicate a few problems, including door lock mechanism failure, loose wire harness going to the control panel, missing or broken door latch. You will want to try unplugging and plugging the washer back in to check for a glitch first. If the door is locked you can access the washer by removing the lower panel under the door, reach up into the washer on the right side until you feel the door latch assembly, then feel for the manual release tab, pull straight down and the door will open. Many times, the latch will need to be replaced.

4. Error Code SUD
This code indicates excess laundry detergent and soap suds. To alleviate this problem, you should first run the load on a rinse cycle and then run it through a regular wash cycle. If this does not work you will need to check your drain hose for kinks or clogs.

These troubleshooting tips can help you solve issues concerning the most common error codes found with the Kenmore Elite Front Load Washer.

Electrolux Ice Maker Troubleshooting

Figuring out why your ice maker isn’t working properly can be frustrating, but with a cool head and a little time you can quickly troubleshoot this problem without the expense of calling in a professional. Your Electrolux ice maker is a wonderful machine that makes your life easy, and you want to make sure it’s in good working condition. If it’s not working though, try the following steps to figure out why:

Check If Your Freezer Is Too Warm.

This may sound like a no-brainer, but it’s common for your freezer to accidentally be above the required range (0 and 5 degrees F) for your ice maker to work properly. Check to see that you haven’t accidentally turned the temperature dial too warm. If that’s set appropriately then make sure that the condenser coils aren’t covered in debris and and that the condenser fan is working the way it should. Another problem that can affect the temperature in your freezer is condensation on the evaporator coils. This can indicate a failure in the system.

Did Your Water Inlet Valve Freeze?

This happens more often than you’d imagine – your water inlet valve may have gotten damaged if you recently moved the freezer or perhaps isn’t getting enough water pressure to function properly. If either of these things happen the valve itself will fill with water and freeze. This will be obvious because where the valve enters the back of the freezer, the valve will be filled with ice.

Did You Put a Kink In a The Water Inlet Valve Fill Tube?

This is insanely easy to do, especially if you’re moving your freezer quickly. When the tube that runs water up into the ice maker gets a kink in it you won’t be able to get water into your ice maker. This, obviously, means that you can’t make ice.

Your Ice Maker May Have a Defective Part.

If your freezer hasn’t gotten too warm for ice to be made and the water inlet valve isn’t frozen then chances are that the problem lies in the ice maker itself. Unfortunately, most ice makers don’t have individual parts available that you can buy to replace or repair a broken piece, so if this is the case you’ll have to buy a new ice maker.

If you have any more questions about why your Electrolux ice maker isn’t making ice then don’t hesitate to call a professional. They’ve seen it all and won’t be judgmental about any problems that you’re having. In face, they may be impressed by the fact that you have checked the temperature, water inlet valve, and fill tube!